Whitney Beam Line Specifications
WHITNEY
BEAM LINE PRESS
DATA |
Capacity |
100
Tons |
Length of stroke |
1-5/8" |
Max. material thickness |
1-1/8" |
Max. hole diameter |
1-1/2" |
Dia. of slug hole |
1-9/16" |
Useable throat depth web press |
18" |
WHITNEY
BEAM LINE TOOLING |
Punch style |
#
770 round all presses |
|
#
790 XX round or shaped |
Die style |
#790 XX all presses |
WHITNEY
BEAM LINE ELECTRICAL
AND HYDRAULIC UNITS |
Control
Voltage |
110V |
Power
Unit |
10HP
220/440/3/60 |
Motor
Control |
Magnetic
Starter |
Conveyor
Drive |
2HP,
SCR Motor |
WHITNEY
BEAM LINE CONVEYORS -
POWERED IN FEED and OUT FEED |
Maximum
work piece length |
up to 60’ |
Maximum
work piece weight |
200 lbs/ft. |
Conveyor speed |
variable 80
ft/mi |
BEAMS |
Max |
Min |
(B)
LIGHT BEAMS: |
31
lb - 16”x 5-1/2" |
9
lb - 6” x 4” |
(W)
WIDE FLANGE BEAMS: |
200
lb - 33”x 15-3/4” |
17
lb - 8” x 5-1/4” |
(M) MISCELLANEOUS BEAMS: |
30
lb - 10” x 5-3/4” |
15
lb - 6" x 6” |
(AS) AMERICAN STANDARD
BEAMS |
120
lb - 24” x -7/8” |
15
lb - 7”x35/8” |
CHANNELS |
Max |
Min |
(C) AMERICAN STD
CHANNEL |
50
lb - 15” x 3-3/8” |
10
lb - 7” x 2-1/8” |
(MC) MISCELLANEOUS CHANNEL |
58
lb - 18” x 4” |
12
lb - 6" x 2-1/2” |
| (MC) MISCELLANEOUS CHANNEL |
58
lb - 18” x 4” |
12
lb - 6" x 2-1/2” |
ANGLE
IRON |
Max |
Min |
|
57
lb 8" x 8” x 1-1/8” |
6
lb 3”x 3” x 5/16” |
PLATE |
Max |
|
140
lb 36" x 1-18" |
WHITNEY
BEAM LINE USER BENEFITS:
-
REDUCED MAN POWER - ONE
MAN CAN DO THE WORK OF TEN MEN
-
REDUCED MATERIAL HANDLING - JUST TWO CRANE PICK’S REQUIRED
(LOAD RAW STOCK - REMOVE FINISHED PART)
-
PUNCHING AND LAYOUT CAPABILITY BOTH ARE ACCOMPLISHED FROM THE CONTROL CONSOLE
-
SHORT OR LONG MATERIAL CAPABILITY
-
CONSISTENT MATERIAL FLOW
-
GIVES PREDICTABLE QUALITY AND
QUANTITY
-
MAKES
ESTIMATING ACCURATE
-
PRODUCES HOLES
ECONOMICALLY
-
ALLOWS SWITCHING TO BOLTED CONNECTIONS FOR LARGE SAVINGS ON FIT-UP WELDING AND INSPECTION.
-
BEAM LINE COMPENSATES FOR CAMBER AND SWEEP -
WILL ACCEPT MILL TOLERANCES
WHITNEY
BEAM LINE SEQUENCE OF OPERATION
The WHITNEY BEAM
LINE model 790-3 MBL features:
Two (2) 100 ton hydraulic FLANGE PRESSES that punch or lay-out both legs of the TOP-FLANGE in one pass. The flange gage is measured from either side of the web with allowance for the thickness of the web.
One (1) 100 ton hydraulic WEB-PRESS is used to either punch holes or lay them out in the web. The web holes are
gauged from the outside of the flange and standard AISC connections can be obtained with the 18” deep throat. The web-gage is measured with direct tape display The web-press carrier incorporates a counter balancing system that allows the press to float vertically to three positions, - die up, stripper down, and center for feeding.
WHITNEY
BEAM LINE MATERIAL HANDLING included with this
machine
-
in feed conveyors powered 40’ OAL
-
Out feed conveyors powered 40’ OAL
-
Three (3) LIFT & CARRY Cross Transfers (PM) design)
-
One (1) Hydraulic Power unit 15 HP ISGPM (PMI design)
|
